英语翻译中

就是把英语翻译为中文，中文翻译为英文就是中译英。满意请采纳，谢谢。

Repair Instructions ___________________A. Remove the necessary fasteners in the area of the damaged skin.Refer to SRM 51-40-02.B. Cut and remove the damaged part of the fuselage skin as shown inFigure 201. Refer to SRM 51-10-02.(1) Make the cut in the shape of a rectangle with the sides parallel orperpendicular to the stringer or frame.(2) Make the corner radii of the cut a minimum of 0.50 inch.C. Put the skin around the cut back to the initial contour.D. Make the repair parts.(1) Make the part [1] doubler. Refer to Table 201. (2) Make the countersink washers for the initial fastener locations inthe initial skin. Refer to SRM 51-40-08.E. Assemble the repair parts as shown in Figure 201.F. Drill the necessary fastener holes. Refer to Table 202 for the fastenertype, diameter, and spacing. Refer to SRM 51-40-05 for the fastener holedimensions.úG. Disassemble the repair parts.H. Remove all the nicks, scratches, burrs, and sharp edges from the repairparts and the bare surfaces of the initial parts.I. Apply a chemical conversion coating to the repair parts and to the baresurfaces of the initial parts. Refer to SRM 51-20-01.J. Install the countersink repair washers with BMS 5-95 sealant at theinitial fastener locations. Refer to SRM 51-40-08.K. Apply two layers of BMS 10-11, Type I primer to the repair parts and thebare surfaces of the initial parts. Refer to SOPM 20-44-04.L. Install the repair parts.(1) Apply BMS 5-95 sealant to the mating surfaces. Refer to SRM51-20-05.(2) Install the rivets without sealant.M. Apply a fillet seal to the repair parts on the internal and externalsides of the repair area with BMS 5-95 sealant. Refer to SRM 51-20-05.N. Apply a finish if necessary. Refer to AMM 51-21-00/701.修理说明___________________A.去除受损皮肤区域的必要紧固件。请参阅SRM 51-40-02。B.如图所示切割并移除机身蒙皮的损坏部分图201.请参阅SRM 51-10-02。（1）以两边平行或平行的长方形切割垂直于纵梁或框架。（2）使切口的角半径最小为0.50英寸。C.将皮肤围绕切割回初始轮廓。D.制作修理部件。（1）制作零件[1]加倍。参见表201。（2）为初始紧固件位置制作埋头孔垫圈最初的皮肤。请参阅SRM 51-40-08。E.如图201所示组装修理部件。F.钻所需的紧固件孔。参见表202了解紧固件类型，直径和间距。请参阅SRM 51-40-05了解紧固件孔尺寸。úG.拆卸维修部件。H.清除修理中的所有刻痕，划痕，毛刺和锐边零件和初始零件的裸露表面。I.在修理部件和裸露部位涂抹化学转化涂层初始部分的表面。请参阅SRM 51-20-01。J.安装带BMS 5-95密封胶的埋头修理垫圈初始紧固件位置。请参阅SRM 51-40-08。K.将两层BMS 10-11，I型底漆涂在修理部件和防护罩上初始零件的裸露表面。请参阅SOPM 20-44-04。L.安装修理部件。（1）在配合面上涂抹BMS 5-95密封剂。请参阅SRM51-20-05。（2）不用密封胶安装铆钉。M.在内部和外部修理部件上涂上圆角封条BMS 5-95密封胶修复区域的两侧。请参阅SRM 51-20-05。N.如果需要，涂抹完成。请参阅AMM 51-21-00 / 701。