
查了一下 里边不包含你的例子组装、冲压、喷漆等专业词汇 Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |'plein|刨床 miller铣床 grinder磨床 driller??床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 to load material上料 to unload material卸料 to return material/stock to退料 scraped |'skræpid|报废 scrape ..v.刮;削 deficient purchase来料不良 manufacture procedure制程 deficient manufacturing procedure制程不良 oxidation |' ksi'dein|氧化 scratch刮伤 dents压痕 defective upsiding down抽芽不良 defective to staking铆合不良 embedded lump镶块 feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车 compound die合模 die locker锁模器 pressure plate=plate pinch压板 bolt螺栓 name of a department部门名称 administration/general affairs dept总务部 automatic screwdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板 stopper阻挡器 flow board流水板 hydraulic handjack油压板车 forklift叉车 pallet栈板 glove(s)手套 glove(s) with exposed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴 iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver起子头 sweeper扫把 mop拖把 vaccum cleaner吸尘器 rag 抹布 garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain链条 jack升降机 production line流水线 chain链条槽 magnetizer加磁器 lamp holder灯架 to mop the floor拖地 to clean the floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机 packaging打包 missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格 dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤 poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆 discoloration羿色 water spots水渍 polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质 delivery deadline交货期 cost成本 engineering工程 die repair模修 enterprise plan = enterprise expansion projects企划 QC品管 die worker模工 production, to produce生产 equipment设备 to start a press开机 stop/switch off a press关机 classification整理 regulation整顿 cleanness清扫 conservation清洁 culture教养 qualified products, up-to-grade products良品 defective products, not up-to-grade products不良品 waste废料 board看板 feeder送料机 sliding rack滑料架 defective product box不良品箱 die change 换模 to fix a die装模 to take apart a die拆模 to repair a die修模 packing material包材 basket蝴蝶竺 plastic basket胶筐 isolating plate baffle plate; barricade隔板 carton box纸箱 to pull and stretch拉深 to put material in place, to cut material, to input落料 to impose lines压线 to compress, compressing压缩 character die字模 to feed, feeding送料 transportation运输 (be)qualfied, up to grade合格 not up to grade, not qualified不合格 material change, stock change材料变更 feature change 特性变更 evaluation评估 prepare for, make preparations for 准备 parameters参数 rotating speed, revolution转速 manufacture management制造管理 abnormal handling异常处理 production unit生产单位 lots of production生产批量 steel plate钢板 roll material卷料 manufacture procedure制程 operation procedure作业流程 to revise, modify修订 to switch over to, switch---to throw--over switching over切换 engineering, project difficulty工程瓶颈 stage die工程模 automation自动化 to stake, staking, reviting铆合 add lubricating oil加润滑油 shut die架模 shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊 vocabulary for stamping 冲压常词汇 stamping, press冲压 punch press, dieing out press冲床 uncoiler & strainghtener整平机 feeder送料机 rack, shelf, stack料架 cylinder油缸 robot机械手 taker取料机 conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点 one stroke一行程 inch寸动 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset复位 smoothly顺利 dent压痕 scratch刮伤 deformation变形 filings铁削 to draw holes抽孔 inquiry, search for查寻 to stock, storage, in stock库存 receive领取 approval examine and verify审核 processing, to process加工 delivery, to deliver 交货 to return delivenry to. to send delinery back to retrn of goods退货 registration登记 registration card登记卡 to control管制 to put forward and hand in提报 safe stock安全库存 acceptance = receive验收 to notice通知 application form for purchase请购单 consume, consumption消耗 to fill in填写 abrasion磨损 reverse angle = chamfer倒角 character die字模 to collect, to gather收集 failure, trouble故障 statistics统计 demand and supply需求 career card履历卡 to take apart a die卸下模具 to load a die装上模具 to tight a bolt拧紧螺栓 to looser a bolt拧松螺栓 to move away a die plate移走模板 easily damaged parts易损件 standard parts标准件 breaking.(be)broken,(be)cracked 断裂 to lubricate润滑 common vocabulary for die engineering模具工程常用词汇 die 模具 figure file, chart file图档 cutting die, blanking die冲裁模 progressive die, follow (-on)die 连续模 compound die复合模 punched hole冲孔 panel board镶块 to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸 Line streching, line pulling线拉伸 engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder文件夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerazation装箱 quantity of physical invetory second count 复盘点数量 quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部-(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用-状况明细表 blank and waste sheet NO. 空白与作废单号 plate电镀 mold成型 material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点 sample样品 incoming material to be inspected进货待验 description品名 steel/rolled steel钢材 material statistics sheet 物料统计明细表 meeting minutes会议记录 meeting type 会别 distribution department分发单位 location地点 chairman主席 present members出席人员 subject主题 conclusion结论 decision items决议事项 responsible department负责单位 pre-fixed finishing date预定完成日 approved by / checked by / prepared by核准/审核/承办 PCE assembly production schedule sheet PCE组装厂生产排配表 model机锺 work order工令 revision版次 remark备注 production control confirmation生产确认 checked by初审 approved by核准 department部门 stock age analysis sheet 库存货龄分析表 on-hand inventory现有库存 available material良品可使用 obsolete material良品已呆滞 to be inspected or reworked 待验或重工 total合计 cause description原因说明 part number/ P/N 料号 type形态 item/group/class类别 quality品质 prepared by制表 notes说明 year-end physical inventory difference analysis sheet 年终盘点差异分析表 physical inventory盘点数量 physical count quantity帐面数量 difference quantity差异量 cause analysis原因分析 raw materials原料 materials物料 finished product成品 semi-finished product半成品 packing materials包材 good product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品 disposed goods处理品 warehouse/hub仓库 on way location在途仓 oversea location海外仓 spare parts physical inventory list备品盘点清单 spare molds location模具备品仓 skid/pallet栈板 tox machine自铆机 wire EDM线割 EDM放电机 coil stock卷料 sheet stock片料 tolerance工差 score=groove压线 cam block滑块 pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差 pocket for the punch head挂钩槽 slug hole废料孔 feature die公母模 expansion dwg展开图 radius半径 shim(wedge)楔子 torch-flame cut火焰切割 set screw止付螺丝 form block折刀 stop pin定位销 round pierce punch=die button圆冲子 shape punch=die insert异形子 stock locater block定位块 under cut=scrap chopper清角 active plate活动板 baffle plate挡块 cover plate盖板 male die公模 female die母模 groove punch压线冲子 air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板 bushing block衬套 insert 入块 club car高尔夫球车 capability能力 parameter参数 factor系数 phosphate皮膜化成 viscosity涂料粘度 alkalidipping脱脂 main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模 demagnetization去磁;消磁 high-speed transmission高速传递 heat dissipation热传 rack上料 degrease脱脂 rinse水洗 alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理 seal封孔 revision版次 part number/P/N料号 good products良品 scraped products报放心品 defective products不良品 finished products成品 disposed products处理品 barcode条码 flow chart流程表单 assembly组装 stamping冲压 molding成型 spare parts=buffer备品 coordinate座标 dismantle the die折模 auxiliary fuction辅助功能 poly-line多义线 heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾 derusting machine除锈机 degate打浇口 dryer烘干机 induction感应 induction light感应光 response=reaction=interaction感应 ram连杆 edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕?? shine亮班 splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒 grit maker抽粒机 cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨 drill铝 boring镗 blinster气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank摸柄 crank shaft曲柄轴 augular offset角度偏差 velocity速度 production tempo生产进度现状 torque扭矩 spline=the multiple keys花键 quenching淬火 tempering回火 annealing退火 carbonization碳化 alloy合金 tungsten high speed steel钨高速的 moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性 resistance电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机 模具工程类 plain die简易模 pierce die冲孔模 forming die成型模 progressive die连续模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce冲孔 forming成型(抽凸,冲凸) draw hole抽孔 bending折弯 trim切边 emboss凸点 dome凸圆 semi-shearing半剪 stamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side stretch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面压印 tick-mark farside反面压印 冲压名称类 extension dwg展开图 procedure dwg工程图 die structure dwg模具结构图 material材质 material thickness料片厚度 factor系数 upward向上 downward向下 press specification冲床规格 die height range适用模高 die height闭模高度 burr毛边 gap间隙 weight重量 total wt.总重量 punch wt.上模重量 五金零件类 inner guiding post内导柱 inner hexagon screw内六角螺钉 dowel pin固定销 coil spring弹簧 lifter pin顶料销 eq-height sleeves=spool等高套筒 pin销 lifter guide pin浮升导料销 guide pin导正销 wire spring圆线弹簧 outer guiding post外导柱 stop screw止付螺丝 located pin定位销 outer bush外导套 模板类 top plate上托板(顶板) top block上垫脚 punch set上模座 punch pad上垫板 punch holder上夹板 stripper pad脱料背板 up stripper上脱料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板 lower plate下模板 die pad下垫板 die holder下夹板 die set下模座 bottom block下垫脚 bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板 inner stripper内脱料板 lower stripper下脱料板 零件类 punch冲头 insert入块(嵌入件) deburring punch压毛边冲子 groove punch压线冲子 stamped punch字模冲子 round punch圆冲子 special shape punch异形冲子 bending block折刀 roller滚轴 baffle plate挡块 located block定位块 supporting block for location 定位支承块 air cushion plate气垫板 air-cushion eject-rod气垫顶杆 trimming punch切边冲子 stiffening rib punch = stinger 加强筋冲子 ribbon punch压筋冲子 reel-stretch punch卷圆压平冲子 guide plate定位板 sliding block滑块 sliding dowel block滑块固定块 active plate活动板 lower sliding plate下滑块板 upper holder block上压块 upper mid plate上中间板 spring box弹簧箱 spring-box eject-rod弹簧箱顶杆 spring-box eject-plate弹簧箱顶板 bushing bolck衬套 cover plate盖板 guide pad导料块 塑件&模具相关英文 compre sion molding压缩成型 flash mold溢流式模具 plsitive mold挤压式模具 split mold分割式模具 cavity型控 母模 core模心 公模 taper锥拔 leather cloak仿皮革 shiver饰纹 flow mark流痕 welding mark溶合痕 post screw insert螺纹套筒埋值 self tapping screw自攻螺丝 striper plate脱料板 piston活塞 cylinder汽缸套 chip细碎物 handle mold手持式模具 移转成型用模具 encapsulation molding低压封装成型 射出成型用模具 two plate两极式(模具) well type蓄料井 insulated runner绝缘浇道方式 hot runner热浇道 runner plat浇道模块 valve gate阀门浇口 band heater环带状的电热器 spindle阀针 spear head刨尖头 slag well冷料井 cold slag冷料渣 air vent排气道 h=0.02~0.05mm w=3.2mm L=3~5mm welding line熔合痕 eject pin顶出针 knock pin顶出销 return pin回位销反顶针 sleave套筒 stripper plate脱料板 insert core放置入子 runner stripper plate浇道脱料板 guide pin导销 eject rod (bar)(成型机)顶业捧 subzero深冷处理 three plate三极式模具 runner system浇道系统 stress crack应力电裂 orientation定向 sprue gate射料浇口,直浇口 nozzle射嘴 sprue lock pin料头钩销(拉料杆) slag well冷料井 side gate侧浇口 edge gate侧缘浇口 tab gate搭接浇口 film gate薄膜浇口 flash gate闸门浇口 slit gate缝隙浇口 fan gate扇形浇口 dish gate因盘形浇口 H=F=1/2t~1/5t T=2.5~3.5mm diaphragm gate隔膜浇口 ring gate环形浇口 subarine gate潜入式浇口 tunnel gate隧道式浇口 pin gate针点浇口 Φ0.8~1.0mm Runner less无浇道 (sprue less)无射料管方式 long nozzle延长喷嘴方式 sprue浇口;溶渣
金属有机源;metal organic source;MO source 含有碳—金属键,适于金属有机化合物化学气相沉积(MOCVD)技术应用的一类金属有机化合物,又称MO源。制备方法有:(1)金属卤化物和格利雅试剂反应;(2)金属卤化物和金属有机化合物反应;(3)金属合金和烷基卤化物反应;(4)金属和格氏试剂进行电化学反应。所得产品经精馏提纯,或与适当的有机化合物生成配合物,除去杂质后再分解得到高纯产品。MO源也可用于金属有机源分子束外延(MOMBE)和化学束外延(CBE)等。
镁是一个年轻的金属,20世纪才发展起来。它呈银白色,熔点649℃,质轻,密度为1.74克/厘米3,约为铜的1/4、铝的2/3;其化学活性强,与氧的亲合力大,常用做还原剂,去置换钛、锆、铀、铍等金属。粉状或细条状的镁,在空气中很易燃烧,燃烧时发出眩目的白光。镁与氟化物、氢氟酸和铬酸不发生作用,也不受苛性碱侵蚀,但极易溶解于有机和无机酸中。镁能直接与氮、硫和卤素等化合。金属镁无磁性,且有良好的热消散性。 镁是地壳中含量高、分布广的元素之一。具有工业价值的矿物有;花菱镁矿、白云石、光卤石。另外,海水也将成为镁资源产地。工业上利用电解熔融氧化镁或在电炉中用硅铁等使其还原而制得金属镁,前者叫做熔盐电解法,后者叫做硅热还原法。 物理性质:质软,熔点较低,成银白色。镁是一种柔软有光泽的金属 化学性质:1.与非金属单质的反应: 2Mg+O2==2MgO 3Mg+N2=Mg3N2 2。与水的反应: Mg+2H2O=Mg(OH)2+H2(加热) 3。与酸的反应:Mg+2HCl+MgCl2+H2 4.与氧化物的反应:2Mg+CO2=2MgO+C(点燃) 元素名称:镁 元素原子量:24.31 元素类型:金属 发现人:戴维 发现年代:1808年 发现过程: 1808年,英国的戴维,用钾还原白镁氧,最早制得少量的镁。 元素描述: 银白色的金属,密度1.74克/厘米3,熔点648.8℃。沸点1107℃。化合价+2,电离能7.646电子伏特,是轻金属之一,具有展性,能与热水反应放出氢气,燃烧时能产生眩目的白光,许多金属是用热还原其盐和氧化物来制备。金属镁能与大多数非金属和差不多所有的酸化合,大多数碱,以及包括烃、醛、醇、酚、胺、脂和大多数油类在内的有机化学药品与镁仅仅轻微地或者根本不起作用。 元素来源: 镁存在于菱镁矿MgCO3、白云石CaMg(CO3)2、光卤石KCl·MgCl2·H2O中,海水中也含镁盐。可以由电解熔融的氯化镁或光卤石制得。 元素用途: 主要用于制造轻金属合金、球墨铸铁、汽车、飞机、科学仪器脱硫剂脱氢和格氏试剂,也能用于制烟火、闪光粉、镁盐等。 元素辅助资料: 镁是在自然界中分布最广的十个元素之一,但由于它不易从化合物中还原成单质状态,所以迟迟未被发现。 长时期里,化学家们将从含碳酸镁的菱镁矿焙烧获得的镁的氧化物苦土当作是不可再分割的物质。在1789年拉瓦锡发表的元素表中就列有它。1808年,戴维在成功制得钙以后,使用同样的办法又成功的制得了金属镁。 从此镁被确定为元素,并被命名为magnesium,元素符号是Mg。Magnesium来自希腊城市美格里西亚Magnesia,因为在这个城市附近出产氧化镁,被称为magnesia alba,即白色氧化镁。不过镁的名称magnesium很容易和锰的名字manganum混淆,虽然有人提出更改,却一直沿用下来。 元素符号: Mg 英文名: Magnesium 中文名: 镁 相对原子质量: 24.305 常见化合价: +2 电负性: 1.31 外围电子排布: 3s2 核外电子排布: 2,8,2 同位素及放射线: *Mg-24 Mg-25 Mg-26 Mg-27[9.45m] Mg-28[21h] 电子亲合和能: -21 KJ·mol-1 第一电离能: 738 KJ·mol-1 第二电离能: 1451 KJ·mol-1 第三电离能: 7733 KJ·mol-1 单质密度: 1.738 g/cm3 单质熔点: 650.0 ℃ 单质沸点: 1170.0 ℃ 原子半径: 1.72 埃 离子半径: 0.66(+2) 埃 共价半径: 1.36 埃 常见化合物: MgO MgCl2 Mg3N2 Mg(OH)2 发现人: 戴维 时间: 1808 地点: 英格兰 名称由来: 来自于希腊Thessaly地区古城邦名“Magnesia”(镁土)。 元素描述: 轻质有延展性的银白色金属。在宇宙中含量第八,在地壳中含量第七。 元素来源: 通常电解熔融的氯化镁(MgCl2)制取。氯化镁可以从海水中提取,每立方英里海水含有约120亿磅镁。 元素用途: 结构特性类似于铝,具有轻金属的各种用途,可作为飞机、导弹的合金材料。但是镁在汽油燃点可燃,这限制了它的应用。
镁是一种银白色的轻金属,元素符号Mg,在元素周期表中属ⅡA族,原子序数12,原子量24.305,化合价为+2,密集六方晶体,密度1.74g/cm3,约为铝密度的64.4%,铁密度的22.1%。由于它的密度小,故把它列为有色轻金属。
由于镁的密度小,又可以与铝、锌、锰、锆、锂、钍、银、稀土等形成一系列的有工业使用价值的镁基合金,故镁又获得最轻的结构金属材料美誉,虽然还有一些金属的密度比镁的小,但它们不能形成有实用价值的结构材料或广为应用的功能性能。由于镁及镁合金密度小,用它们取代钢、铸铁、铝等制造交通运输装备零部件可大幅度减轻其自身质量,节能减排效果卓著,不过提取镁的能耗不比提取铝的低。镁还有21世纪绿色金属的美称,用途会越来越广,大有用武之地。
镁还有具有许许多多优秀的化学性能和冶炼性质,因此它在各种非结构应用中也有着广泛的使用,扮演着重要的角色。
镁是一种非常活泼的金属,尚未在自然界中发现有纯净的镁存在,但它是自然界分布很广的重要有色金属,属二价碱土金属,约占地壳总质量的2.45%,可见镁资源的丰富,使它成为第八种丰富的化学元素和第六种丰富的金属元素。镁是地壳中储量多的第三种结构金属,仅次于铝和铁。
镁现身人间已有213个年头,1808年英国化学家戴维(Humphry Davy)找到了镁,宣布镁的诞生。那一年,他确定一种白色的氧化物是一种从未发现的新的金属的化合物,那就是氟化镁。他在实验室使用钾蒸汽通过热的氧化镁,并用汞提取被还原的镁,获得镁汞齐,他还用汞作阴极电解了硫酸镁,也制得了一种汞齐形式的镁,这是人们首次制的金属镁,他所用的氧化镁产自希腊的Mognesia(马格尼西亚)州,于是将这种新发现的命名为Magnesia,以后根据元素的拉丁文统一命名法改为拉丁文Magnesium,中国则根据ma的谐音给它取了个悦耳动听的名字“镁”。不过戴维制得的镁不是相当纯净的,肯定含有一定量的种种杂质。
在此需指出,许多人在镁之前冠以“金属”二字,迈格镁业小严建议中国不要用金属镁一词,因为“镁”带有金字旁,就说明它是一种金属,这是汉字的绝妙之处。但在翻成英文时又应说成“Metal Magnesium”,这是他们的习惯,同时从“Magnesium”也看不出来它是金属还是非金属,因而在前面加metal顺理成章。
希望采纳,更多镁合金信息,大家可以关注百业网络
镁是地壳中含量高、分布广的元素之一。具有工业价值的矿物有;花菱镁矿、白云石、光卤石。另外,海水也将成为镁资源产地。工业上利用电解熔融氧化镁或在电炉中用硅铁等使其还原而制得金属镁,前者叫做熔盐电解法,后者叫做硅热还原法。